Hot Wire Foam Factory All Purpose Foam Coat 25lb #025ECO-25

Description: Fast Shipping - Made in the USA - Quality Customer Service Hot Wire Foam Factory All Purpose Foam Coat 25lb #025BULK-25 Hot Wire Foam Factory #025BULK-25 All Purpose Foam Coat Proudly made in the USA! Includes: 1 25lb Box of All Purpose Foam Coat Details: All purpose foam coat! This rock-hard cement-like coating protects and beautifies your foam projects. Comes in a dry powder - simply mix with water. It's tough but still sandable. It is inherently fire resistant. Can be used outdoors when sealed with any outdoor paint, or mixed with Boost liquid fortifier, or Bounce liquid rubberizer. Apply thick with a trowel or thin with a paintbrush. Sets up in only about 15 minutes. Extend the drying time by adding up to 50% latex paint with your water before mixing into the dry foam coat. Compatible with our Boost, Bounce, and Grit! Features: Adheres to polystyrene foams. Forms a tough, protective surface. Easy to mix. Just add water. Use above or below grade. Apply with paintbrush or trowel. Paintable Fireproof Many decorative surface textures can be created. Soap and water clean-up. Add Boost fortifier if extra strength is desired. Add Bounce for a rubbery, flexible surface texture. INSTRUCTIONS: MIXING: Settling may occur in shipping causing a gritty texture that does not stick well. Remix if there is separation in dry mixture. Use when temperatures are between 40°F (4°C) and 100°F (38°C). Mix in a clean container with clean water. Add about 3 parts powder to 1 part water and mix until Foam Coat turns to a smooth paste. A drier mix is stronger. Do not overmix. APPLYING: If using extruded foam (ie Blueboard or Pinkboard) roughen surface with coarse sandpaper. Fill big cracks and holes by applying pasty mixture with a trowel. You may add more water until mixture is thin enough to apply with a paint brush, although thinning weakens coating. Can be applied with a standard spray hopper. Use thinned mixture to texture large areas. For best strength apply at least 1/4" (6mm) thick. Multiple coats may be applied. Try texturing surface before coating sets. SET TIME: Use within 30 minutes. Sets up in 1-3 hours. Fogging the surface for 24 hours will increase strength. FINISHING: Remove dust before painting. This product goes on rough and is not sandable. Finish as the surface is setting up. CLEAN-UP: Clean tools and brushes with clean soapy water before coating hardens. WARNING: Avoid prolonged contact with skin. Wear dust, skin and eye protection. Use approved respirator when sanding. In case of eye contact, flush immediately with water, consult a physician. Wash hands with soap and water after use and before eating. Keep out of reach of children. COVERAGE 25lbs: 1/64” thick 288 sq ft 1/16” thick 72 sq ft 1/4” thick 18 sq ft COMPRESSIVE STRENGTH: ASTM C109 1 Day 750 psi 7 Day 2500 psi 28 Day 3500 psi FLEXURAL STRENGTH: ASTM C348 1 Day 350 psi 7 Day 550 psi 28 Day 1250 psi FIRE DATA Flammability: Noncombustible and not explosive. Auto-ignition Temperature: Not Applicable Flash Points: Not Applicable PAYMENTSHIPPINGWARRANTY/RETURNSPAYMENTSHIPPINGWARRANTY/RETURNSWe accept payment by any of the following methods: PayPal, Visa, Amex, Discover, MasterCard Buyers in California will be charged 8% sales tax. Please pay as soon as possible, as that will allow us to ship your item to you sooner! Packages are always insured. We ship within 2 business days (So if you order Monday, your order will ship by Wednesday). Weekends and holidays do not count as business days. We are not responsible for any customs fees, duties, taxes or tariffs imposed by the destination country which you may have to pay. USA - FedEx & USPS (United States Postal Service) Canada/Mexico - USPS (United States Postal Service) International Worldwide (Except Hong Kong or China) - USPS (United States Postal Service) International Limited Warranty & Limitation of Liability Information: This product is warranted for non-commercial use as follows: For 90 days from the original date of purchase, HWFF, Inc. will, at its option, repair or replace a defective unit free of charge, if the unit is defective due to an original manufacturer’s defect. This warranty covers normal use and does not cover damage which occurs in shipment or unit failure which results from alteration, accident, misuse, abuse, or neglect. Except as herein expressly set forth, HWFF, Inc. shall not under any circumstances be responsible for any direct, indirect, incidental, or consequential damage resulting from the use of the equipment. The consumer’s sole remedy shall be such repair or replacement as expressly provided above. Return Policy: HWFF, Inc. retains the exclusive and sole right as to whether an item may be returned, exchanged, or order cancelled. HWFF, Inc. thus encourages customers to use caution when placing an order, as once placed the order cannot be cancelled, nor the item returned or exchanged unless HWFF, Inc. expressly consents. In order to obtain a refund or exchange, prior approval must be given by HWFF, Inc.. Generally, HWFF, Inc. will consider returns within thirty (30) days of purchase with a 20% restocking charge. Refunds are for the cost of product only; shipping and handling charges are not refundable. Buyer is responsible for return shipping. Please ask any questions you may have prior to buying. Hot Wire Foam Factory #025BULK-25 All Purpose Foam Coat Proudly made in the USA! Includes: 1 25lb Box of All Purpose Foam Coat Details: All purpose foam coat! This rock-hard cement-like coating protects and beautifies your foam projects. Comes in a dry powder - simply mix with water. It's tough but still sandable. It is inherently fire resistant. Can be used outdoors when sealed with any outdoor paint, or mixed with Boost liquid fortifier, or Bounce liquid rubberizer. Apply thick with a trowel or thin with a paintbrush. Sets up in only about 15 minutes. Extend the drying time by adding up to 50% latex paint with your water before mixing into the dry foam coat. Compatible with our Boost, Bounce, and Grit! Features: Adheres to polystyrene foams. Forms a tough, protective surface. Easy to mix. Just add water. Use above or below grade. Apply with paintbrush or trowel. Paintable Fireproof Many decorative surface textures can be created. Soap and water clean-up. Add Boost fortifier if extra strength is desired. Add Bounce for a rubbery, flexible surface texture. INSTRUCTIONS: MIXING: Settling may occur in shipping causing a gritty texture that does not stick well. Remix if there is separation in dry mixture. Use when temperatures are between 40°F (4°C) and 100°F (38°C). Mix in a clean container with clean water. Add about 3 parts powder to 1 part water and mix until Foam Coat turns to a smooth paste. A drier mix is stronger. Do not overmix. APPLYING: If using extruded foam (ie Blueboard or Pinkboard) roughen surface with coarse sandpaper. Fill big cracks and holes by applying pasty mixture with a trowel. You may add more water until mixture is thin enough to apply with a paint brush, although thinning weakens coating. Can be applied with a standard spray hopper. Use thinned mixture to texture large areas. For best strength apply at least 1/4" (6mm) thick. Multiple coats may be applied. Try texturing surface before coating sets. SET TIME: Use within 30 minutes. Sets up in 1-3 hours. Fogging the surface for 24 hours will increase strength. FINISHING: Remove dust before painting. This product goes on rough and is not sandable. Finish as the surface is setting up. CLEAN-UP: Clean tools and brushes with clean soapy water before coating hardens. WARNING: Avoid prolonged contact with skin. Wear dust, skin and eye protection. Use approved respirator when sanding. In case of eye contact, flush immediately with water, consult a physician. Wash hands with soap and water after use and before eating. Keep out of reach of children. COVERAGE 25lbs: 1/64” thick 288 sq ft 1/16” thick 72 sq ft 1/4” thick 18 sq ft COMPRESSIVE STRENGTH: ASTM C109 1 Day 750 psi 7 Day 2500 psi 28 Day 3500 psi FLEXURAL STRENGTH: ASTM C348 1 Day 350 psi 7 Day 550 psi 28 Day 1250 psi FIRE DATA Flammability: Noncombustible and not explosive. Auto-ignition Temperature: Not Applicable Flash Points: Not Applicable Fast Shipping - Made in the USA - Quality Customer Service Hot Wire Foam Factory All Purpose Foam Coat 25lb #025BULK-25 Hot Wire Foam Factory #025BULK-25 All Purpose Foam Coat Proudly made in the USA! Includes: 1 25lb Box of All Purpose Foam Coat Details: All purpose foam coat! This rock-hard cement-like coating protects and beautifies your foam projects. Comes in a dry powder - simply mix with water. It's tough but still sandable. It is inherently fire resistant. Can be used outdoors when sealed with any outdoor paint, or mixed with Boost liquid fortifier, or Bounce liquid rubberizer. Apply thick with a trowel or thin with a paintbrush. Sets up in only about 15 minutes. Extend the drying time by adding up to 50% latex paint with your water before mixing into the dry foam coat. Compatible with our Boost, Bounce, and Grit! Features: Adheres to polystyrene foams. Forms a tough, protective surface. Easy to mix. Just add water. Use above or below grade. Apply with paintbrush or trowel. Paintable Fireproof Many decorative surface textures can be created. Soap and water clean-up. Add Boost fortifier if extra strength is desired. Add Bounce for a rubbery, flexible surface texture. INSTRUCTIONS: MIXING: Settling may occur in shipping causing a gritty texture that does not stick well. Remix if there is separation in dry mixture. Use when temperatures are between 40°F (4°C) and 100°F (38°C). Mix in a clean container with clean water. Add about 3 parts powder to 1 part water and mix until Foam Coat turns to a smooth paste. A drier mix is stronger. Do not overmix. APPLYING: If using extruded foam (ie Blueboard or Pinkboard) roughen surface with coarse sandpaper. Fill big cracks and holes by applying pasty mixture with a trowel. You may add more water until mixture is thin enough to apply with a paint brush, although thinning weakens coating. Can be applied with a standard spray hopper. Use thinned mixture to texture large areas. For best strength apply at least 1/4" (6mm) thick. Multiple coats may be applied. Try texturing surface before coating sets. SET TIME: Use within 30 minutes. Sets up in 1-3 hours. Fogging the surface for 24 hours will increase strength. FINISHING: Remove dust before painting. This product goes on rough and is not sandable. Finish as the surface is setting up. CLEAN-UP: Clean tools and brushes with clean soapy water before coating hardens. WARNING: Avoid prolonged contact with skin. Wear dust, skin and eye protection. Use approved respirator when sanding. In case of eye contact, flush immediately with water, consult a physician. Wash hands with soap and water after use and before eating. Keep out of reach of children. COVERAGE 25lbs: 1/64” thick 288 sq ft 1/16” thick 72 sq ft 1/4” thick 18 sq ft COMPRESSIVE STRENGTH: ASTM C109 1 Day 750 psi 7 Day 2500 psi 28 Day 3500 psi FLEXURAL STRENGTH: ASTM C348 1 Day 350 psi 7 Day 550 psi 28 Day 1250 psi FIRE DATA Flammability: Noncombustible and not explosive. Auto-ignition Temperature: Not Applicable Flash Points: Not Applicable PAYMENTWe accept payment by any of the following methods: PayPal, Visa, Amex, Discover, MasterCard Buyers in California will be charged 8% sales tax. Please pay as soon as possible, as that will allow us to ship your item to you sooner! SHIPPING Packages are always insured. We ship within 2 business days (So if you order Monday, your order will ship by Wednesday). Weekends and holidays do not count as business days. We are not responsible for any customs fees, duties, taxes or tariffs imposed by the destination country which you may have to pay. USA - FedEx & USPS (United States Postal Service) Canada/Mexico - USPS (United States Postal Service) International Worldwide (Except Hong Kong or China) - USPS (United States Postal Service) International WARRANTY/RETURNS Limited Warranty & Limitation of Liability Information: This product is warranted for non-commercial use as follows: For 90 days from the original date of purchase, HWFF, Inc. will, at its option, repair or replace a defective unit free of charge, if the unit is defective due to an original manufacturer’s defect. This warranty covers normal use and does not cover damage which occurs in shipment or unit failure which results from alteration, accident, misuse, abuse, or neglect. Except as herein expressly set forth, HWFF, Inc. shall not under any circumstances be responsible for any direct, indirect, incidental, or consequential damage resulting from the use of the equipment. The consumer’s sole remedy shall be such repair or replacement as expressly provided above. Return Policy: HWFF, Inc. retains the exclusive and sole right as to whether an item may be returned, exchanged, or order cancelled. HWFF, Inc. thus encourages customers to use caution when placing an order, as once placed the order cannot be cancelled, nor the item returned or exchanged unless HWFF, Inc. expressly consents. In order to obtain a refund or exchange, prior approval must be given by HWFF, Inc.. Generally, HWFF, Inc. will consider returns within thirty (30) days of purchase with a 20% restocking charge. Refunds are for the cost of product only; shipping and handling charges are not refundable. Buyer is responsible for return shipping. Please ask any questions you may have prior to buying. Hot Wire Foam Factory #025BULK-25 All Purpose Foam Coat Proudly made in the USA! Includes: 1 25lb Box of All Purpose Foam Coat Details: All purpose foam coat! This rock-hard cement-like coating protects and beautifies your foam projects. Comes in a dry powder - simply mix with water. It's tough but still sandable. It is inherently fire resistant. Can be used outdoors when sealed with any outdoor paint, or mixed with Boost liquid fortifier, or Bounce liquid rubberizer. Apply thick with a trowel or thin with a paintbrush. Sets up in only about 15 minutes. Extend the drying time by adding up to 50% latex paint with your water before mixing into the dry foam coat. Compatible with our Boost, Bounce, and Grit! Features: Adheres to polystyrene foams. Forms a tough, protective surface. Easy to mix. Just add water. Use above or below grade. Apply with paintbrush or trowel. Paintable Fireproof Many decorative surface textures can be created. Soap and water clean-up. Add Boost fortifier if extra strength is desired. Add Bounce for a rubbery, flexible surface texture. INSTRUCTIONS: MIXING: Settling may occur in shipping causing a gritty texture that does not stick well. Remix if there is separation in dry mixture. Use when temperatures are between 40°F (4°C) and 100°F (38°C). Mix in a clean container with clean water. Add about 3 parts powder to 1 part water and mix until Foam Coat turns to a smooth paste. A drier mix is stronger. Do not overmix. APPLYING: If using extruded foam (ie Blueboard or Pinkboard) roughen surface with coarse sandpaper. Fill big cracks and holes by applying pasty mixture with a trowel. You may add more water until mixture is thin enough to apply with a paint brush, although thinning weakens coating. Can be applied with a standard spray hopper. Use thinned mixture to texture large areas. For best strength apply at least 1/4" (6mm) thick. Multiple coats may be applied. Try texturing surface before coating sets. SET TIME: Use within 30 minutes. Sets up in 1-3 hours. Fogging the surface for 24 hours will increase strength. FINISHING: Remove dust before painting. This product goes on rough and is not sandable. Finish as the surface is setting up. CLEAN-UP: Clean tools and brushes with clean soapy water before coating hardens. WARNING: Avoid prolonged contact with skin. Wear dust, skin and eye protection. Use approved respirator when sanding. In case of eye contact, flush immediately with water, consult a physician. Wash hands with soap and water after use and before eating. Keep out of reach of children. COVERAGE 25lbs: 1/64” thick 288 sq ft 1/16” thick 72 sq ft 1/4” thick 18 sq ft COMPRESSIVE STRENGTH: ASTM C109 1 Day 750 psi 7 Day 2500 psi 28 Day 3500 psi FLEXURAL STRENGTH: ASTM C348 1 Day 350 psi 7 Day 550 psi 28 Day 1250 psi FIRE DATA Flammability: Noncombustible and not explosive. Auto-ignition Temperature: Not Applicable Flash Points: Not Applicable

Price: 84.95 USD

Location: Lompoc, California

End Time: 2024-08-16T16:10:08.000Z

Shipping Cost: 0 USD